Idle this weekend

  
   If you have followed this race this past weekend, you know that Paul and the Beast weren't on hand.
Paul said a combination of too much construction work and not enough time to get the car fully ready  -- plus the 11-hour drive down there -- persuaded him to keep the Beast parked.
    However, the new engine and refurbished transmission are in the car, and he's close to being able to fire it up. Though the season is winding down, big races remain on the calendar  -- all at place where Paul has run.
First is the Southern Shootout series finale at Montgomery in two weeks, followed by the PDRA finals in Virginia and another race in the Carolinas, that I think is at Shadyside.
     We'll have an update closer to the Montgomery race.

Let's crank this season up

   It's a big weekend for promod racing, with a PDRA event at Rockingham and the Southern Shootout opener at the Super Chevy Show in Memphis, but rather than travel hundreds of miles, Paul and the Beast team are staying closer to home for this NMCA event that is basically just down the road -- at Atlanta Dragway at Commerce, Ga.
   Paul has run well at Atlanta, and also experienced a crazy mishap a couple of years ago when his competition ran into him in the shutdown area. The race is an easy decision -- proximity, good payout and a level field. It's an all-run race -- but there are rules to make it even for blowers (no screws), nitrous, and I guess turbos.
   The team will get set up today for two rounds of qualifying on Friday and Saturday, one round of racing on Saturday, and the conclusion on Sunday.
   The Beast made just one of two test sessions that were on the calendar last month -- at Montgomery Motorsports Park. The track was hosting an Edmund Hall event, but Paul said track prep wasn't minimal, so the team didn't learn much from a couple of test passes. He said they took about 500 horsepower out of the motor, but the Beast still lost traction about 60 feet out. "If the track had been prepped, it might have held the car," Paul said. The team did not go to a test session at U.S. 43 the following week.
   As noted, it's a busy week for racing. I'm sure promodifieds.us will be covering Memphis, and there will be plenty of links to the PDRA event, but I'll keep an eye out for any Atlanta news.
   All racers: Be fast and be safe.

It's 2016, and almost time for racing

          It has been a long time away from the track, but Paul and the Cuda Beast team are getting fired up for their return after a 2015 season that was a tough one away from the racing. Crew member Keith Dockery, who spent most of last year in various hospitals, is getting better, "more like himself every day," Paul said.  This weekend, the team had a party at the shop to get things kicked off.
         The season will start next weekend with a test session at Montgomery Motorsports Park. Last year,  Paul had a conversation with a top pro-mod tuner who had run sub-4s with the same engine and setup that's in the Beast. The tuneup was radically different from what the team had been using, so Paul decided to tear down the motor and get the transmission refurbished so the car would be at peak readiness for the new tuneup. He didn't get to try it before the season ended, but will finally at MMP next weekend.
        It's a much more aggressive tuneup, which sounds counterintuitive for a car that's had problems getting launched. More power when you're blowing off the tires?  That's it. Paul said if they blow off the tires, they'll back down on the tuneup until the car launches. He said if the tuneup works out, he's expecting even better results than his tuner source got because the Beast is a couple of hundred pounds lighter.
       The MMP session will be followed the next weekend with more testing at U.S. 43 Dragway in Etheridge, Tenn.  The first weekend in April is the first big racing weekend, with the PDRA at Rockingham and a Southern Shootout event at the Memphis Super Chevy Show. Also that weekend, just 90 minutes or so down the road, will be a pro-mod event at the NMRA NMCA All-Star Nationals, and that's where Paul said he's planning to take the Beast.
      As far as the rest of the season is shaping up, PDRA events are definite possibilities. I'll post any test session results I learn. Round up your earplugs. The big noise is ready to return.

It's race day!

     Paul and the Beast will be at Montgomery this weekend for the promodifieds.us Southern Shootout finale. That point series has already been decided, but it should be a terrific race nonetheless, as Montgomery and the Southern Outlaw Tour always put on a great show. It's a screw-blower series, but Paul is eager to try out the Beast's new tuneup at a track where he has run well before.
     Thursday, the Beast was all ready to be loaded up. Paul was in the process of putting the refurbed transmission back into his truck. That will mean he'll miss tonight's qualifying, but will have two shots and a test run or two Saturday. Since he was really busy, I didn't get into plans about next weekend's PDRA race. One at a time.
     Crew member/computer guru Keith Dockery is still having a tough go with medical issues, so keep him in your thoughts and prayers.
     As this is a promodifieds.us - affiliated race, the fantastic Brian C will be trackside to provide his peerless reporting and photography all day Saturday. Check the message board at promodifieds.us frequently. It's almost as good as being there.
    OK, everybody -- be fast and be safe. 

Into the homestretch

       As you might have guessed by now, Paul and the Beast did not make it to last month's Open Outlaw race at Huntsville. The engine was still out of the car then, but should be back in and ready to go for a possible visit to Montgomery this coming weekend.  It's the final race of the promodifieds.us Southern Shootout series, which has already been decided by Dwayne Watkins' dominating performances this year. But it should be a strong field, and Paul is eager to try the Beast's new tuneup against the screw-blower cars.
     In this downtime from racing, Paul has also worked on his hauler and the transmission in his truck. Paul said he's also interested in the season closer for the PDRA, which would be in Virginia. Paul ran pretty well there last year in the tough pro boost class. The PDRA would mean back-to-back racing weekends for the team, so we'll see.
     Paul said crew member and computer guru Keith Dockery should be going back home this month, finally after months of medical issues.
    We'll have an update on the end-of-season races as Montgomery approches.  

2015 season: Montgomery called off

    Dang.
    The weather hex that bedeviled the season at Montgomery Motorsports Park last year is still around, as this weekend's 2015 opener has been called off because of an iffy forecast. It was going to be the first race for Paul and the Cuda Beast this year -- basically a test opportunity to check out tweaks to the tuneup that hopefully will get the car launching better off the line as the team looks to its first real race -- the PDRA event at Rockingham, N.C., April 9-12.
   Not sure what the team's plans are now leading up to Rockingham; a race the weekend before at Huntsville could serve as a test session, but back-to-back weekends are tough for them. We'll let you know.

2015 season: Ready to race

    The 2015 season for Paul Gibbs and the Cuda Beast team got off to this neat start, courtesy of the PDRA featuring the Beast in its promotion for its opening race of the year in Texas. The pic is early in the 2014 season, maybe from the PDRA event in Memphis (looks like his huge holeshot race against Joe Baker; you can go back a few posts and see pictures from that event), as the car has its double wheelie bar setup.
   The Texas event is a long shot, basically a couple of days on the road each way; Paul said the team is pursuing possible monetary sponsorship from a source that has connections that go back to the racing days of his father, Reece Gibbs. Should that materialize, the Texas race would be in play. Still, it's a kick to see the Beast get national notice. Hard to go wrong with one of the best-looking PM cars out there.
    There is a real first race on the calendar -- the Southern Shootout opener at Montgomery Motorsports Park March 13-14. The series is the South's prime screw-blower hangout; Paul didn't run the Beast in that series last year for that reason, preferring the PDRA's popular Pro Boost class and some EOPM events. He says he's certainly ready to race at Montgomery, but is really viewing the weekend as a test session for the team's first PDRA race, in April at Rockingham (unless the Texas longshot comes through). Hope its a warm weekend for a change. A brine solution could be part of track prep.
    As far as the car goes, Paul says DJ Safety (see this page's masthead) has updated all of his equipment, including a state-of-the-art engine containment "diaper" (which we hope will never see use). Paul is promising a picture, which we'll post when it arrives.
   We'll be back to set up the Montgomery race/test session.

     

No racing this weekend

    A combination of events will keep the Cuda Beast in its garage this weekend, instead of hitting the track at Montgomery Motorsports Park for the season's last Southern Outlaw Tour race. The Beast's torque converter is on its way to PTC for some work, as Paul said the tolerances of some important pieces are off by a few hundredths, meaning they don't fit together properly. Also, chilly weather, at least by racing standards, has settled over the South for the past several days and will run through the weekend. That means a cold track and iffy racing conditions. Finally, Paul has agreed to fill in at his church this Sunday while the pastor is out of town to conduct a revival, so he was possibly looking at getting back home in the early hours of Sunday morning, grabbing a shower and maybe a couple of hours of sleep, and getting up in the pulpit.
      So, the Beast will remain idle throughout November, and then head way south to Bradenton Motorsports Park, near Tampa-St. Petersburg, for a big three-day race the first weekend in December. Paul said it will be a 9-to 10-hour drive, but the temperatures should be fine for racing.
     With 2013 winding down, Paul had been looking east for 2014, to the Carolinas at a no-screw-blowers series, but it just announced that it will cease operations after a 10-year run, and will hold its final race this weekend. Paul said there is another Carolina series that is a possibility, and maybe some races at Lassiter Mountain. Of course, the Cuda Beast team could join the pro mod technology arms race, but that takes gobs of money and thus is not something Paul can do without major sponsorship, as he's largely financing his racing out of his own wallet.
    We'll preview the Bradenton race after Thanksgiving. Have a great one.

Huntsville recap: Unhappy on the starting line

   The Cuda Beast's timing controller had bad timing in more ways than one at Huntsville last weekend. Paul and the Cuda Beast team headed to the Rocket City full of optimism, with the engine at full strength and backfiring problems likely solved. But the first test pass revealed that the timing controller, added when the Beast switched from a clutch setup to an automatic for this year, was not working. Paul said today he had been suspicious of it for a while, but Saturday, the suspicion was confirmed.
   The 4 seconds or so of a run are sliced and diced into intervals of tenths of seconds by the timing controller -- pulling timing out of the engine at the start to get the car off the line, and putting it back in at various levels for the rest of the run (that's my layman's understanding of it; hope it's reasonably accurate). It's hard to imagine that such tiny changes, happening so quickly, could have such big effects, but they do. Paul's controller wouldn't pull timing out at the start, so the Beast blazed the tires at the start, killing any chance of a decent pass.
    With the controller not working, Paul took a guess at the timing to get the car off the line -- timing it would have for the entire pass. No luck. The team passed up the first round of qualifying, readjusted the timing and went out for round two and blew the tires. They dropped the timing again for the third round, but again the Beast killed the tires.
    Saturday's racing wrapped up fairly early, so Paul said he set about trying to find someone who had a spare controller like his, an "8973."  In asking around, Paul said he found out that 8973s had fallen out of favor, and a new and less-expensive device, called a "grid," was now in wide use. A fellow at Huntsville had a rolling chassis for sale that had a grid, and he let Paul borrow it for the Beast. After church Sunday, Paul and the Beast went out for the final qualifying round with the grid, and took a stab at the timing, the lowest Paul said he has ever used at the start. The Beast spun the tires all the way to a 4.39, and the same went on in the second-chance race. Paul bought the grid controller, and is now looking to Montgomery in a couple of weeks.
     Paul said he talked with the mechanic for another team, who said Paul needed to consider one of two factors to get the car launched: blower boost or backing the timing off. Paul said he now has a boost graph to look at that is a picture of the boost for an entire run. He said he's inclined to leave the boost alone, and concentrate on the timing to get the car off the line. "We're not shaking the tires. We're spinning them," he said. "We have a mountain of torque -- we've got to harness it."
    So, Paul plans to hit the track at Montgomery as soon as it's ready, to get at least a couple of test runs before qualifying starts. If the Beast responds and hits its potential, somewhere in the high 3's, that meet will wrap the season. If the right combo is still elusive, Paul says they'll look for other races. "We'll go to Florida if we have to. We'd like to end in the 3.90s, and know where we are going into the next year."
    We'll be back in a couple of weeks to set up the Montgomery race.    
    

Huntsville recap, and a weekend off

   

    Last weekend's race at Huntsville was a pretty good one for the Cuda Beast in terms of performance and knowledge gained. Paul ran a 4.17, a season's best, to take seventh in a tough 8-car field that had the fastest cars running 3.70. He went out in the first round against the No. 2 qualifier and blew a burst panel at the finish line.
    Some of the times for the weekend were definitely suspicious, but the track assured Paul that his 4.17 was good, and Paul said he could really feel the G-forces in the driver's seat. Most interesting was a 60-foot .095, which is essential to sub-4 times. But 100-150 feet out, the tires smoked just a bit, and the Beast then hazed the tires the rest of the run, leaving two black strips down the track. So, a 4.17 with the tires not fully hooked up for most of the run was definitely encouraging.
    The blown burst panel brought back the backfiring problem that Paul had hoped he had solved with a new distributor cap. This latest episode got him to thinking about what happens deep inside the engine. He said he's never run a lot of valve spring pressure to keep from breaking parts, but the backfiring indicates that valves aren't fully closed when they should be. Plus, blower boost acts to reduce the actual valve spring pressure. After discussing the situation with his valve spring supplier, Paul said he's going to bump up the valve spring pressure for the next race.
    About the next race, Paul had this weekend's SOT event at Montgomery on the calendar, but he's passing (and weather may cancel it, anyway) it up to work on the engine and get ready for a race next weekend at Orangeburg, S.C. The engine passed a leak-down test after the latest backfire, but Paul says oil from the No. 8 cylinder indicates a ring problem, so No. 8 is getting a new piston and rings this weekend.
    Returning to Orangeburg after a couple of years brings up memories of a crash and fire, but Paul says that's all just history. The appeal of the race is that no screw blowers are allowed, which levels the racing field. More and more ADRL-spec cars are turning up at the races the Beast attends now, which means its 3.90s capability would still not be competitive. Though the payout at Orangeburg isn't as much, the chance to win it is much better without screw cars in the field.
    In fact, racing in the Carolinas next year is a definite possibility because of the ban on screws. Paul says he would be ready to go to a screw setup, but that would require sponsorship, which he doesn't have. We'll preview Orangeburg next week.        

Goin' back to Huntsville, Huntsville, Huntsville . . .

      Not exactly the same effect of the old Dean Martin lyric, but Paul and the Cuda Beast team are hoping for big hits this weekend at the Bama Nationals. The last outing for the Beast was also Huntsville, where it eked into the field and lost in the first round to top qualifier/track record holder/eventual winner Dwayne Watkins. At that race, the Beast was basically running as a six-cylinder, as Paul found blown head gaskets in a postrace engine check, with two cylinders leaking badly.
     All that has been fixed, and a backfiring problem has also been dealt with by a new, extra large distributor cap. With all of those factors cleared up, the Beast will run with its current torque converter setup to see how it takes the healthy engine. Paul said the team will arrive today and set up, and hopes to make a couple of test passes Saturday afternoon, before the evening qualifying sessions. Paul said he hopes to hit the track soon after it opens for testing and a few cars go down.
    This race is an eight-car field, and has drawn some criticism for its scheduling across two days, qualifying Saturday evening and racing on Sunday afternoon. There have been indications that some racers may pass this one up, so it's hard to say how large and tough the field will be. I'm not sure what the coverage will be online, but check the message board at www.promodifieds,us , and if I hear anything from Paul, I'll try to pass it along. Next weekend will be Montgomery and the Southern Outlaw Tour. Safe, fast racing for all.

Good hunch

    Computers are a huge help to drag racers, giving them a complete picture of the performance of all the systems on a race car during a run down the track. However, seat-of-the-pants intuition remains essential.
    As the Cuda Beast's lagging 60-foot times pointed to the need for a different torque converter configuration, Paul also suspected from the driver's seat that the engine seemed weak. Last weekend, Paul decided to perform a leakdown test on the motor, and found that cylinders 1 and 8 were leaking, 8 especially. Paul said normal leakdown on his motor is no more than 6-7 percent; cylinder 8 was 35 percent, enough that air could be heard and felt. That indicated a blown head gasket -- detected early enough that the Beast dodged damage to the head and/or block that would have ended the season. Paul had new head gaskets on hand, and at the end of a long day in the shop, the Beast's hemi passed a new leakdown test with flying colors.
    Still, the Beast will have new computer info available at the next race, back at Huntsville, with a new device that will give a readout on engine boost for the entire run. Also, the fuel management system will be all in for the race. "We're going to throw everything we've got at it, all the technology we've invested in," he said. If all the pieces fall into place in the next few races and the Beast starts to meet its potential consistently -- 3.90s and even high 3.80s -- Paul said he would be likely to keep his roots blower setup and forgo a switch to a costly screw blower. Nailing the torque converter configuration will yield big gains. The Beast had .098 60-foot times with its old clutch setup; Paul said the converter should drop that to .094 or better.
    The schedule is Huntsville and Montgomery this month and next month, for a total of four races to wind up the season.   

Huntsville recap

       This time last weekend, Paul and the Cuda Beast were at Huntsville, with a drivetrain all at 100 percent, a good feel for the tuneup and high hopes for some 3-second passes.  Alas, it was more time spent on the learning curve, and the realization that the torque converter, though mechanically fit, lacked the right configuration.
     The first qualifying run, a 4.49 at only 135 mph, was because the car wasn't shifting into high gear. The team went through the drivetrain and found the Lenco out of adjustment. Subsequent passes, the computer data revealed weak 60-foot times, Paul said, a best of .101 when the ideal would be down in the .0990s. Plus, the .101s couldn't even be repeated. "We had tried all the starting line procedures we could try -- more aggressive, less aggressive," Paul said, with no improvement, which all pointed to the torque converter. "We were driving right through it."
    Strong 60-foot times usually yield strong runs, so the converter is going back to PTC for a makeover, and the Beast will be back at Huntsville in two weeks for the Bama Nationals (eight-car field), and then the weekend after that at Montgomery.
    Still, the 4.49 got Paul into the race at the 16th spot, apparently when a quicker car had mechanical problems. That put him against No. 1 qualifier and new Huntsville track record-holder Dwayne Watkins, who had a new hemi engine under the hood and ran 3.70s at more than 200 mph. Paul got him at the line and the Beast ran a 4.36, but Watkins took over quickly, shutting off early for a 3.91. He went on to win the event. Paul said Watkins' new motor was a proven 3.60s piece bought from ADRL hitter Bubba Stanton, who sold it with just a 3.80s tuneup, leaving Watkins to figure out the rest of it. Looks like he's on his way.
    Paul said the growing presence of "screw" blowers may force him to evaluate his setup for next year. As currently configured, the Beast easily has sub-4-sec. potential, even high 3.80s, but the expensive screw setups are bringing 3.70s to the southern outlaw arena, so 3.90s likely won't get it done. This equipment escalation may have lots of teams trying to figure out what to do, and whether, lacking sponsorhip, they can afford it.
      We'll be back before the next race in two weeks with info on the torque converter situation.  

Cuda Beast to staging

   That's right -- finally, there will be racing this weekend. Huntsville Dragway is the site -- historically one of the Beast's best tracks -- with 16 cars going for $5,000. The field of competitors will likely be huge, and could include cars that run occasionally, if not regularly, in ADRL. The weather is looking good, though it will be hot, and the track record is in definite jeopardy.
   (FRIDAY MORNING UPDATE: Got a call from Paul, passing through Chattanooga en route to Huntsville. The plan is to try to make a test run this evening -- testing is open from 5-11 p.m.-- which would be useful for the first two rounds of qualifying on Saturday night. Paul said if he looks like he's solidly in the field after rounds one and two, he'll forgo the final qualifying round Sunday morning.)
    Paul has the transmission/torque converter back in proper working order, and is ready for his first 3-second pass. He has just one race on his new Mickey Thompson tires, but says they are by far the best he's ever run.
   After this race, here is the rest of the Beast's 2013 schedule:
   

September

Sat 14 & Sunday 15 - Bama Nationals @ Huntsville  

Fri 20 & Sat 21 - Montgomery SOT  

October

Fri 11, Sat 12 & Sun 13 - Huntsville Rocket City Nationals 

Fri 25 & Sat 26 - Montgomery SOT  
   
    September will be busy with back-to-back weekends, but they are both excellent tracks and promise exciting racing. As for this weekend, you can find the complete flier for the race on the message board at www.promodifieds.us with all of the information you need to know. Also, Brian C. should be there to provide his sterling coverage, so check the message board for updates if you can't make the race.
    Be safe, and be fast.

The craziness continues

     This year’s unpredictable season found new tangents on and off the track in the past couple of weeks. Paul and the Cuda Beast team had to forgo last week’s Central Alabama Pro Mod Series races while the transmission was getting sorted out to try to fix the problem of the car rolling through the starting beams. Paul was in second place, just three points behind Tim Segars, who at the time wasn’t expected to be racing that weekend, either.
    Well, Segars did race and won both events, pretty much locking up the points title. Paul is conceding as much, and doesn’t plan to run the series’ last dates next month. (A possible driving job for Ron Stokes didn’t pan out, either, as Stokes’ regular driver was at the wheel.) Paul said the Beast’s remaining races will take place at Huntsville and Montgomery, where the team was headed this weekend.
    When I talked to Paul on Tuesday, he was checking the bottom end of the motor and awaiting receipt of  his repaired transmission on Wednesday. As suspected, the bands were bad, which meant the line lock wouldn’t work properly, but a pump on the front of the transmission was also found to have failed, possibly due to exposure to excessive heat. With the pump not working, that meant the torque converter was also not working as it should.
    After we hung up, Paul kept rolling the transmission woes around in his mind and thought to look at the torque converter, and saw that it looked like it had suffered some damage. He called PTC in Muscle Shoals, and they said they’d be in the shop at 6 a.m. Wednesday to take care of things, so Paul was immediately en route to Alabama.  I  got all this from Paul Wednesday as he was driving back from PTC, getting ready to put all the new pieces back in the car and head to Montgomery.
      While this was going on, Mother Nature, who has rained out events all summer long, hit the Montgomery area with a severe storm, and a lightning strike at the track fried most of the wiring and timing equipment, postponing the race yet again. Track owner Jim Howard says he hopes to have things fixed by the middle of next week, but no new race date has been set. The next outing for the Beast could be Aug. 24 at Huntsville, though there are other possibilities in between.
      Needless to say, Paul was really looking forward to Montgomery. The car has run more consistently this year, in the 4.20s even with the sick drivetrain, and Paul is confident that he’s dialed in on the engine tuneups. With the trans and torque converter both healthy, and the new Mickey Thompson tires that he says are the best he’s ever run, Paul says he wants to hit the 3-second zone “now.”
     When the race schedule firms up, we’ll be back.

Huntsville recap: "A lot of fun"

      That's how Paul Gibbs summed up the weekend for the Cuda Beast team at Huntsville's Rocket City Nationals. The car delivered a big run, loves its new Mickey Thompson tires, but got bit again by the line lock problem. But Paul and the team learned a lot, and will be ready for the next race, which will likely be at Montgomery Motorsports Park in two weeks.
      Paul went 4.26 at 165 in round one qualifying and didn't beat that, which left him about ninth fastest. The race was split into blower and nitrous classes, with an "all run" format. The eliminations were on a 16-car bracket for the dozen or so cars, and the four fastest got byes. That created a tight bunch racing for the next round, and Paul was right in the middle, running Jim Kyle, who qualified just a few hundredths faster. Paul says he doesn't try to max out his tuneup for every race, but rather goes for what he thinks he'll need to win. Kyle surprised him by running his best of the meet, but the Beast also improved. Though slower than Kyle, Paul's big holeshot (above), got the win.
     With the fastest qualifiers back in the mix for the next round, Paul drew a tough match in top qualifier Dwayne Watkins, who has been on a tear lately.  The Beast had been blowing burst panels all weekend, and the culprit turned out to be a clogged fuel filter. Paul said he put in a "3.97-4.02 tuneup" in the car for Watkins and hoped to beat him off the line, but the Beast rolled through the beams, and Watkins went 3.89.
     Still, it was a good weekend. "I love the new tires. They're unbelievable," Paul said of his first outing on the new Mickey Thompsons. "The stability on them is better than any tire I've ever run." Paul said he's really confident on the tuneups now, so the next thing to figure out is the linelock problem. The car was rock steady on the line until the Watkins race, and Paul suspects something's amiss inside the transmission.
     Digging into the transmission and making the usual postrace engine inspections will sideline the Beast this coming weekend, even though it's a Central Alabama Pro Mod series points weekend. Paul is second with 11, three behind Tim Segars and three ahead of several other drivers. Segars won't be racing this weekend, either, while he fixes his car, so Paul figures not to give up too much ground. However, Paul may be driving in the series this weekend for Ron Stokes. We'll be offline this weekend, so check the message board at promodifieds.us for any race info this Friday and Saturday.

     

Montgomery . . . ? (Yes) (No)

     5:30 p.m. Saturday UPDATE: Mother Nature strikes again during this racing season. Rain interrupted first round of qualifying. Stopped long enough to resume, then more rain, and the race was cancelled. Too bad. It's been a nice day here, 300 miles to the west.
     It's the second no-go for this SOT event. I don't know whether Paul tested Friday night or Saturday, but his first qualifying pass was an off-the-pace 6.25. Photo looked like he might have smoked the tires after launching. Looks like it will be Lassiter Mountain on July 3rd for another make-up race, for the Central Alabama Pro Mod Series. Sorry to say, but the weather looks iffy again.    

7:00 p.m. UPDATE: Just got Paul on the phone at Montgomery. Weather has cancelled a round of qualifying for tonight, but racers can test, and Paul is getting ready to make a pass. The team is shorthanded this week as Keith Dockery is out with injured ribs, but they will give it their best. The race is on for tomorrow -- 2 qualifying rounds and then eliminations. Will be a 16-car field if the car count is high enough.
    Last time I talked with Paul, he said the Cuda Beast team was planning to make this weekend's SOT race at Montgomery. However, I haven't been able to contact him the past couple of days, so I don't know if that's still the plan. There will be race info on the message board at www.promodifieds.us , so you can check there, as I'll be doing. The weather looks a bit iffy, but this is a makeup of an earlier race, so I'm betting that anything short of a monsoon, the race is on. The racers and promoters are eager to get things going, that's for sure.
    If I hear anything, I'll post it. Paul and the team also have a July 3 makeup event for the Central Alabama Pro Mod series. Haven't seen a points standing lately, but I'm guessing Paul is probably second. Hope there's lots of safe, fast racing this weekend.

Weekend update: Red-light blues

    Paul and the Cuda Beast team had a couple of one-and-dones this past weekend in the Central Alabama Pro Mod Series, red-lighting both times against Jimmy Sandefur, who went on to the finals in both races. Tim Segars won at Lassiter Mountain on Friday, and John Sullivan on Saturday at Holiday Beach. Haven't seen a points list, but Paul and Segars were tied for first going in; Segars should be on top alone after his win, even though he had mechanical problems the next night. No one was within two-tenths of him during eliminations.
    The team barely made the first round of qualifying at Lassiter after a fuel line came loose on a test run, causing the engine to lean out and blow a burst panel. Paul got an ovation from the crowd for a great save on his first qualifying run when the Beast got sideways at 450 feet. That run was 4.515, for fourth place. Round two improved to 4.477, and the first round red-light was a 4.41 that had Sandefur's 4.64 covered easily. An observed noted that the Beast seemed to have trouble staying in the starting beams. Paul said the trans brake was having difficulty holding the car, and that he most likely staged too deep, which led to the red-light. Next outing, the car will have line locks front and rear.
    Paul said Holiday Beach was pretty slick on the top end, but he still powered to a weekend best  of 4.33 in round two of qualifying, down from a 4.38. He said the Beast started hazing the tires about two-thirds of the way down, but he stayed in it all the way, to the crowd's delight. "It wasn't that big of a pass, but I got tired of lifting," he said. Though the red-light determined the first-round outcome, the Beast also lit the tires immediately into the run.
     The next race will be at Montgomery, a Southern Outlaw Tour event on June 29, followed on July 3 with a midweek makeup of a rained-out points race at Lassiter Mountain. Some new tires are on the way from Mickey Thompson, and the team continues to work with the fuel management system to help the car get through a tire-shake zone when it shifts into high gear, about 2.7 seconds into a run.
    Paul is also getting his Dart street car ready for its closeup at the drive-in in Blue Ridge, where filming is going on for "Need For Speed," a movie about a cross-country race based on a video game franchise.

June 7: Testing

    Lots of stuff has happened/is happening since the last post, so let's get caught up:
    When we last checked in, the Cuda Beast team had loan of a dually from fellow racer David Elsberry, after Paul's red Dodge lost all its oil and blew up on I-20 last month. Since then, Paul decided to look for another truck, found one in St. Louis, and picked it up this week. It's a 2007 Dodge, with a bigger engine and stouter drivetrain. It's white, and makes for a visually longer rig when coupled to the white trailer. When Paul gets the engine fixed for the red truck, it will be for sale (contact us if you are interested).
    After last month's weather-related cancellations, the plan was to race this weekend at the Southern Outlaw Tour at Montgomery, but that race has been rescheduled. With the Central Alabama ProMod series resuming next weekend at Lassiter Mountain and Holiday Beach, and with a new untested engine setup in the car, Paul, the team and the new truck are headed to Alabama International Raceway in Steele, Ala., tomorrow for a test session. There's a big bracket meet going on, but testing will be allowed from noon to 6 p.m.
    Paul says Steele has tons of traction and the track will be well-prepped even though the event is not a full-out promod race. He hopes to get dialed in there, and then see if Lassiter Mountain will hold that setup; if not, they'll back it off until it does. Paul and the Cuda Beast team are tied for first in the Central Alabama series points after one race.
   

March 23: SOT weekend report

    Going into last weekend's Southern Outlaw Tour event at Montgomery Motorsports Park, Paul Gibbs said he was viewing the event primarily as test session to get ready for the Central Alabama pro-mod series he will run this year -- but if he made the SOT field, great.
      The Beast was on the bubble after two rounds of qualifying with a 4.36, and couldn't improve on that and was bumped from the field. The team is still chasing the setup with the new automatic transmission, but was happy to see that the transmission leaks that were common last year have now been stopped. Also, the car's "lazy" 60-foot times indicated the engine was too lean, Paul said.
     The Central Alabama series involves racing at two tracks -- Lassiter Mountain and Woodstock -- on consecutive days, and starts April 5.